In this section you will learn about the router commands, configurations, privileged mode commands, routing protocols, cisco labs and network configurations.

There are hundreds of basic and advance level commands of a router. It is not easy to remember all the commands. But some commands are frequently used and can be remembered with some practice. I have provided a list of the most commonly used commands based on their features and usage.You will find here some basic terminology of a router.

Routing: Routing is a process of moving the data (packets) through an inter network. Routing performs the two basic tasks. Define the paths for a packet and then forward the packets on the basis of defined paths. Routing can also be defined as the communication between two or more logically and physical networks and this communication (packet transfer) is brought by a router.

First of all you should remember the keyboard shortcuts of a router.

Keyboard Shortcuts

CTRL-N - show next command
CTRL-P - show previous command
SHIFT-CTRL-6 – Break

Configuring the Router

You will be able to learn the basic commands for configuring a router.
sh running-config - details the running configuration file (RAM)
sh startup-config - displays the configuration stored in NVRAM
setup - Will start the the automatic setup; the same as when you first boot the router
config t - use to execute configuration commands from the terminal
config mem - executes configuration commands stored in NVRAM; copies startup-config to running-config

config net - used to retrieve configuration info from a TFTP server
copy running-config startup-config - copies saved config in running config (RAM) to NVRAM or "write memory" for IOS under ver.11
copy startup-config running-config - copies from non-volatile (NVRAM) to current running config (RAM)
boot system flash <put file filename here> - tells router which IOS file in flash to boot from
boot system tftp - tells router which IOS file on the tftp server to boot from
boot system rom - tell router to boot from ROM at next boot
copy flash tftp - Copies flash to tftp server
copy tftp flash - Restores flash from tftp server
copy run tftp - Copies the current running-config to tftp server
copy tftp run - Restores the running-config from tftp server

General Commands

Here is a list of the general commands. These are the basic level commands and most commonly used
no shutdown - (enables the interface)
reload - restarts the router
sh ver - Cisco IOS version, uptime of router, how the router started, where system was loaded from, the interfaces the POST found, and the configuration register
sh clock - shows date and time on router
sh history - shows the history of your commands
sh debug - shows all debugging that is currently enabled
no debug all - turns off all debugging
sh users - shows users connected to router
sh protocols - shows which protocols are configured
banner motd # Your customized message here # - Set/change banner
hostname <give router name> - use to configure the hostname of the router
clear counters - clear interface counters

Privileged Mode commands of a router

Learn how to work in the privileged mode of a router.
enable - get to privileged mode
disable - get to user mode
enable password <give password here> - sets privileged mode password
enable secret <give password here> - sets encrypted privileged mode password
Setting Passwords on router
Here you will be able to learn how to set the password on a router.
enable secret <give password here> - set encrypted password for privileged access
enable password <give password here> - set password for privileged access (used when there is no enable secret and when using older software)
Setting the password for console access:
(config)#line console 0
(config-line)#login
(config-line)#password <put password here>
Set password for virtual terminal (telnet) access (password must be set to access router through telnet):
(config)#line vty 0 4
(config-line)#login
(config-line)#password <put password here>
Set password for auxiliary (modem) access:
(config)#line aux 0
(config-line)#login
(config-line)#password <put password here>

Router Processes & Statistics

By these command you can see the statistics and different processes of the router.
sh processes - shows active processes running on router
sh process cpu - shows cpu statistics
sh mem - shows memory statistics
sh flash - describes the flash memory and displays the size of files and the amount of free flash memory
sh buffers - displays statistics for router buffer pools; shows the size of the Small, Middle, Big, Very Big, Large and Huge Buffers
sh stacks - shows reason for last reboot, monitors the stack use of processes and interrupts routines